Contents
The sensing light begins to blink when a new wash cycle starts. While this is perfectly normal, if you notice that the light keeps blinking for too long, it means the washer is stuck on the sensing phase. This usually indicates an issue with the load size, sensor, a faulty equator, or clogged drain pump..
Why will my Whirlpool washer not start?
How do I run a diagnostic on my Whirlpool washer?
Why is my washing machine not starting?
First, make sure the power is on and that the machine is plugged in. You should check the outlet to make sure it’s working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated.
Why did my Whirlpool washer stop working?
Check to make sure the washer is still plugged in. Over time, washers have a tendency for their plugs to become loosened due to excess agitation from an uneven load. 2. Make sure the circuit breaker in your electrical panel box has not been tripped.
How do I read a Whirlpool error code?
How do I reset my Whirlpool white magic?
Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
How do you calibrate an automatic washing machine?
Why is it important to use calibration mode?
- Remove all laundry or any other contents in the machine.
- Power off, and then power on the washing machine on again.
- Hold down Temp.
- Press START/PAUSE to run the Calibration cycle.
- The drum will rotate clockwise and counterclockwise for about 3 minutes.
How do I reset my Whirlpool Cabrio Top load washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
What to do if my washer is stuck on sensing?
Another likely cause of the issue is a clogged water inlet valve- it happens a lot if there have been repairs on the main water line so check if sand or other stuff is clogging either inlet valve. Simply turn off water then remove hose and proceed to clean the screen (on the valves at the washer).
How do I force my Whirlpool washer to unlock?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
What is Whirlpool diagnostic mode?
Whirlpool Belt Drive Washer Diagnostic Mode & Tests
The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.
What are the codes on a Whirlpool washer?
Error Codes in your Whirlpool Top Load Washer:
| Error code | Error |
|---|---|
| LF, Lo FL or F8 E1 | The washer is taking too long to fill. |
| lid | The washer lid was left open. |
| Ofb | The washer load is out of balance. |
| OL | The washer load too large. |
• Jun 15, 2020
How do you calibrate?
On Windows, open the Control Panel and search for “calibrate.” Under Display, click on “Calibrate display color.” A window will open with the Display Color Calibration tool. It steps you through the following basic image settings: gamma, brightness and contrast, and color balance.
How do I fix a Whirlpool washer that won’t spin?
What causes a washing machine not to drain and spin? If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do I manually drain my Whirlpool washer? If not, follow these steps:
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose at the back of the washing machine.
- Step 3: Drain the water.
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose.
- Step 3: Drain the water.
- Step 4: Scrub the filter.
How long does a Whirlpool washer stay on sensing?
These sensing spins may take 2 to 3 minutes before water is added to the load. The washer will then move the load briefly, pause to allow water to soak into the load, and resume adding water. This process may repeat until the correct amount of water has been added to the load.
What does calibrating a washer do?
Except for preventing vibrations and noise, calibration also makes sure you save energy. After calibration, the load sensor more accurately weighs your laundry. This means the washing cycle can better adjust itself to to the amount of clothes, which saves time and energy.
Why is my Whirlpool washer not draining or spinning?
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
Why won’t my washing machine finish its cycle?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
What to do if washer stops working?
1 Be sure the machine is plugged in and turned on. If necessary, check the receptacle it’s plugged into for power, using a working lamp, appliance, or voltage tester. Be sure the washer lid is closed completely. 2 If the receptacle seems dead, check the circuit breaker or the fuse that serves it.
How do you bypass the lock on a Whirlpool washer?
How do you open the Control Panel on a Whirlpool washing machine?
Locate the screws on the left and right sides of the bottom of the front or rear of the control panel, depending on model. Remove the two screws and then rotate the control panel up 180-degrees to access the interior components of the panel.
How do I reset my Whirlpool front loader door lock?
