Why is my U-verse TV not working?

Try this first. Restart your TV receiver by holding the POWER button down for 10 seconds then pressing it again to restart. This process takes 5-8 minutes and will impact any DVR recordings in progress. Restart your Wi-Fi^® Gateway by removing the power cord for one minute then plugging it back in..

How do I reboot my ATT Uverse DVR?

Restart your U-verse TV receiver (DVR) by holding down the POWER button for 5 seconds, then press it again to restart. (This takes 5-8 minutes and impacts any DVR recordings in progress.) Press the Recorded TV button on your remote if your recorded program is frozen or missing.

Why is my ATT U-verse box not working?

Many receiver problems can be fixed by restarting your receiver. To do this, press and hold the Power button for 10 seconds. This takes 5-8 minutes and will impact any DVR recordings in progress. If you have multiple receivers, reboot your wireless gateway by unplugging it from its power source.

What to do when DVR is not working?

DVR Troubleshooting

1. Make sure your equipment (TV and cable) is properly connected and powered on.
2. Make sure the coax cable is connected to the outlet.
3. Remove any objects around your receiver to allow proper ventilation.
4. Refresh your receiver.
5. Unplug your receiver and wait at least 60 seconds before plugging it back in.

Why is my wireless receiver not working?

Sometimes the receiver gets out of sync with the wireless devices, causing them to stop working. Resyncing the setup is fairly easy. There is usually a Connect button somewhere on the USB receiver. Press that, and a light on the receiver should start flashing.

How do I restore my DVR recordings?

You can restore events that have been deleted from the DVR if it’s been less than 48 hours since they were deleted.

1. Press the DVR button.
2. Select Trash.
3. Arrow to and select the recording you want to restore.
4. Press the BLUE COLOR or Recall button, depending on your remote.

Why does my DVR cut off the end of shows?

Some programs run a little past the scheduled end time. To handle those, use the “extend” function to add a minute or more. This will cause the DVR to use a different tuner (not “line”) to record the start of the next show.

Why is my DVR deleting shows?

Most likely, you were out of hard drive storage space and the DVR automatically deleted the oldest recorded shows. Shows are only kept until more room is needed, however you can protect shows from deletion from the Recorded TV category.

Can a DVR wear out? The hard drive in your DVR is designed to work for close to a decade with only minor issues. It’s always being checked in little ways. However, sometimes damage does occur due to wear and tear.

Is AT&T discontinuing U-verse?

U-verse TV is no longer available for new customers. Current U-verse TV customers can continue to access their service here. DIRECTV STREAM offers live and local sports games in more markets than any other live streaming service.

Where is the power button on U-verse receiver?

Check power.

Confirm you have power. If you have power and the receiver is turned on, the Power button on the front of your AT&T U-verse receiver will have a green light surrounding it.

Why does my DVR not record sometimes?

The most common reasons for the Spectrum DVR recording issues are attributed to lack of storage space, incorrect cable connections and cache memory build up in the device.

Why did my DVR not record?

If your Spectrum Guide DVR is powered on and you can play back recorded shows but can’t record new programming, it’s likely because you don’t have enough storage space. Try deleting some recorded shows to see if that provides you with the extra space you need.

How can I make my DVR record longer?

How do I extend the recording time on my DVR? Here’s how it works:

1. Schedule a live broadcast recording – press the R on your remote.
2. View on-screen message asking if you’d like to extend the recording time.
3. The default setting extends recording by 30 minutes.
4. Modify the extension from 1 minute up to 3 hours.

How do I get my DVR to stop recording a series? To stop automatically recording episodes of a TV series:

1. Press the DVR button on your remote control and select Scheduled.
2. Highlight an upcoming episode of the series and press OK.
3. Select GET MORE INFO.
4. Select VIEW SERIES INFO.
5. Select CANCEL RECORDING and confirm on the next screen.

How do I delete shows from my DVR? To delete a single-show recording

1. Press on the remote control, select DVR from the menu, and press ok.
2. Using the remote, browse your recordings to find the show you want to delete.
3. Select the recording and press ok.
4. Select Delete and press ok.

Why is my AT&T router not working?

Power cycle (reboot) your AT&T gateway – Unplug the gateway from the power outlet in the wall and wait two minutes before plugging it back in. After the Power, Broadband, and Service lights on your gateway turn green, verify that your connection has been restored.

Why is my DVR glitching?

DVR skipping occurs due to network or hardware issues. A poor network signal along with incorrect placement of the DVR, can cause a DVR to skip. A DVR is a device that helps you record multiple videos to a disk drive, memory card, or a local mass storage device in a digital arrangement.

How do I fix my AT&T Wi-Fi?

Wi-Fi gateway

1. Unplug the power cord from the back of your gateway or modem. If you have:
2. Wait 20 seconds.
3. Put the internal battery back in, if applicable.
4. Plug the power cord back in.
5. Wait up to 10 minutes for the gateway or modem to restart and your Broadband light to turn solid green.

Why does my DVR cut off the end of shows?

If your DVR cuts off the end of a program, this is due to a delay in processing the signal through the cable system.

Why won’t my DVR let me delete a recording?

If you have a recording that will not delete, please review the following steps to resolve the issue: On your remote, press CABLE then the MENU button twice. Select the DVR MENU then choose DVR CLEANUP. Check the program to delete and click DELETE on the left.

What was Teevo?

The TiVo is the least successful, most significant consumer electronics device ever. When it came out in early 1999, it was one of the first two digital video recorders (DVRs), the other being the digital video recorder from ReplayTV, which was introduced at almost the same time.

How do I reboot my DVR?

Press and hold the Power button located on the front of the primary DVR TV Box for 10 seconds . The TV Box should automatically reboot.

Or:

1. Ensure your cables are tightly secured.
2. Unplug the power from your primary DVR TV Box for 30 seconds.
3. Plug the power cord back in to your TV Box.

Will I lose my recordings If I unplug my DVR? Your recordings will be fine. Unplugging your DVR is no different than unplugging and rebooting a PC.

How do you delete shows from Direct TV?

Press List on the remote. That should bring up your recorded items. Select which recordings you would like deleted and press the delete button.