Contents
December 2, 2021. Oven Repair. If your GE oven is displaying an F9 error code, it means that there is a problem with the oven’s door lock. The door lock is automatic and stays locked when your oven is running through a cleaning cycle..
What does F9 error code mean?
Personal injury and damage to the oven can result. An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock.
How do I unlock my oven profile?
How do I fix my Whirlpool E1 F9?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.
How do I reset my F9 Whirlpool stove?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
How do I put my Whirlpool oven in diagnostic mode?
How do I stop my Whirlpool stove from beeping?
Reset power to the product:
Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the cooktop for one (1) minute to ensure the error code does not display again.
Why does my washer keep saying E1 F9?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation.
What does F9 E1 mean? The Whirlpool washer F9E1 error code is a long drain error, meaning its taking too long for the washer to drain the water.
How do I clear E1 F9 code?
How to Fix Whirlpool Washer E1/F9 Error Codes
- Try a Reset. Sometimes an error code is caused by a control board glitch, where resetting the washer is all it takes to resolve the error code.
- Check your Detergent.
- Check the Drain Hose.
- Clean the Filter.
- Check the Drain Pump.
- Check the Wiring.
How do I fix error code F9E1 on a Whirlpool washer?
Clean the drain pump filter and the bellows drain holes (see Cleaning and Maintenance symptom above). Check the drain hose for obstructions and verify installation.
Drain Issues
- Drain Pump on the Washer/dryer may need to be cleaned.
- The bellows drain holes may be obstructed.
- The drain hose may be obstructed.
How do I manually unlock my Whirlpool oven door?
Possible Solutions
- Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door.
- Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.
- Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
Why is my Whirlpool oven door locked?
It’s often because the control panel lock was set inadvertently. Holding down the START button for 3 seconds should clear the setting and unlock the door.
How do I unlock my self-cleaning oven door?
How do I unlock my electric stove?
How do you unlock a Whirlpool stove top? To unlock the control panel, press and hold CONTROL LOCK for 3 seconds. The indicator light will turn off, and the appliance is ready for use.
Why does my oven keep saying locked?
When an oven is in a self-cleaning cycle it turns up to a very high heat temperature. This is to make sure all the extra dirt and food debris burn off. To prevent any injuries during this period, your oven will automatically lock itself so that no one can open it and get exposed to extreme heat.
How do I turn off the control lock on my Whirlpool oven?
Press and hold the Options key for 3 seconds to turn off Control Lock.
How do you unlock a Whirlpool stove?
Door is locked when starting or using the oven
Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
How do I turn off the control lock on my Whirlpool oven?
To turn the control lock setting off, press and hold the START button for 3 seconds. If this doesn’t work, turn the oven off at the circuit breaker for 1 minute. When the circuit breaker is turned back on, the error code should be gone.
How do I turn off the control lock on my oven?
To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
How do I clean my Whirlpool drain pump?
Place a broad, flat container beneath the drain pump filter to collect the drain water. Release the black hose from the hose clip, remove the plug, and drain the hose into the container. Empty the container. Repeat this procedure if necessary until all the water has drained.
How do you clear the error code on a Whirlpool top load washer?
Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online.
Where is the drain pump filter on my Whirlpool Duet? The location of the drain pump filter in a Whirlpool Duet washer is accessible through the lower access panel below the washer door.
