Contents
Press the “Off/Clear’ button for three seconds to turn the “Control Locked” child lock off. Reset the cooking program if “Off/Clear” was pressed accidentally. For example, press the “Defrost” button again, and turn the dial to select the defrost time you want again. Press “Start.”.
How do I run a diagnostic on my Whirlpool oven?
How do you reset a stove after a power outage?
How To Reset Your Oven After a Power Surge: 5 Steps
- Step 1: Check the Breaker Box.
- Step 2: Make Sure the Fuses Are Still Good.
- Step 3: Check the Power Cord.
- Step 4: Reset the Electronic Control Panel.
- Step 5: Try to Give the Oven a Cycle To Complete.
- The Control Panel Is Locked.
- You Have the Delay Start Turned On.
How do I reset my F9 Whirlpool stove?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
How do I reset my Whirlpool oven after a power outage?
Look for “Control Lock” on the oven control console and then reset by typically holding the button(s) for 3 seconds.
How do I know if my oven element is blown?
If the element is blistered or separated, then it should be replaced. If the element appears to look normal, then turn the oven on to a bake function for a minute and then turn it off. Check the element for signs of heating and if it is still cold then it may be defective.
What does F9 mean on an electric stove?
Personal injury and damage to the oven can result. An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. The automatic door lock mechanism prevents the oven door from being opened when the oven is set for “Clean” mode.
What does it mean when your oven says F9?
An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. The automatic door lock mechanism prevents the oven door from being opened when the oven is set for “Clean” mode.
How do you unlock a Whirlpool stove top? To unlock the control panel, press and hold CONTROL LOCK for 3 seconds. The indicator light will turn off, and the appliance is ready for use.
How do I reset my f9 Whirlpool stove?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
Why is my Whirlpool oven not heating up?
A Whirlpool oven not heating evenly can also be due to a defective temperature sensor. This component works with the control panel to regulate an oven’s temperature fluctuations. If the temperature sensor is malfunctioning, it won’t accurately communicate these fluctuations, resulting in uneven cooking.
Why does my oven say F9 EO?
During a power outage, if there was a surprising amount of power supply line “noise” that the control detected as an incorrect voltage amount, the control could display the F9, F9 E0, or PF Error Code.
What does F8E0 mean on oven?
F8E0 and F8E2 – Cooling fan speed too low or too high
That was in the early days of this error. Whirlpool started shipping the sensor with the fan. So, to cure the problem, just replace both, and you should be good to go.
Why is my Whirlpool oven beeping?
A Whirlpool oven can keep beeping because of a faulty temperature gauge, control panel or keypad. What is this? Continuous beeping from your Whirlpool oven could indicate a problem. Sometimes you can resolve it by simple pressing the cancel button and resetting the oven.
Why did my Whirlpool oven stop working? If the thermal fuse does not have continuity, replace it. The thermal fuse cannot be reset—if the fuse has blown, it must be replaced. One of the wires that supply power to the oven element or igniter might be burnt out. These wires commonly burn out near the heat source.
How do I know if my oven fuse is blown?
What do I do if my oven isn’t heating up? Solved! Why Your Oven Isn’t Heating Properly—and How to Fix It
- If an electric oven is completely dead, check the breaker.
- Check the position of the oven and stove knobs.
- Consider replacing an electric oven’s heating element.
- Clean the igniter on a gas stove.
- Check the temperature sensor.
How do you reset an oven?
Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.
How do I reset my Whirlpool oven?
Reset power to the product:
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Start a bake cycle.
- Monitor the oven for one (1) minute to ensure the error code does not display again.
- Verify oven operation.
Why does my stove top work but not my oven?
In most common cases, this specific issue means that the broil element and the baking element remain functional. However, there’s probably a blown internal fuse. If it’s not the fuse, it could be the temperature sensor, broken or frayed wiring, or even a breakdown of the oven control board.
How do I reset my oven control board?
To reset it, just unplug the oven then wait about a minute then plug it back in. This should reset the board and clear any errors that are causing problems (if that is the case).
Why is my oven not working after a power outage?
Check the Breaker – A damaged or compromised breaker is the most common cause of performance problems. Check the breaker and reset it to see if the oven is working. If the breaker smokes or burns again, stop using the appliance and call an expert.
How do I fix F1 error on Whirlpool oven?
F1 Error Code
There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.
How do you unlock the control panel on a Whirlpool stove?
To turn the control lock setting off, press and hold the START button for 3 seconds. If this doesn’t work, turn the oven off at the circuit breaker for 1 minute. When the circuit breaker is turned back on, the error code should be gone.
How do I fix my oven that is not heating?
