Contents
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub..
How do I fix e01 f09 error?
1 – You may have a drain hose that is bent and not letting the water drain out – Check the back of the washer. 2 – Be certain the drain hose height does not exceed 96″ or the washer cannot drain properly. 3 – Clean the drain pump filter on the bottom front of the washer of any particles or objects.
How do you clean the pump filter on a Whirlpool drain?
Place a broad, flat container beneath the drain pump filter to collect the drain water. Release the black hose from the hose clip, remove the plug, and drain the hose into the container. Empty the container. Repeat this procedure if necessary until all the water has drained.
How do I clean my Whirlpool Duet drain pump?
Place a broad, flat container beneath the drain pump filter to collect the drain water. Release the black hose from the hose clip, remove the plug, and drain the hose into the container. Empty the container. Repeat this procedure if necessary until all the water has drained.
How do I read a Whirlpool error code?
Where is the drain filter on a Whirlpool Duet washer?
How do you remove the front panel on a Whirlpool Duet washer?
Open the washer door and insert a flathead screwdriver into the slot in the bottom center of the console above the door opening. Push the control console cover up to release the console tab in the center. Lift the control console cover up, and set it out of your way.
What does F09 mean on a Whirlpool washing machine?
Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
How do I fix error code F28? An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit. Rebooting the control unit is accomplished in less than 10 minutes, even by the novice.
How do I reset my f9 Whirlpool stove?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
What does E1 and F9 mean on a Whirlpool washer?
What is the error code E1 F9 related? The cause must be sought in the drain system. A sign of fault is unsuccessful attempts of the drainage pump to pump out water. If it cannot do this the first time, it restarts in 5 minutes and then switches off.
How do I unlock my Whirlpool oven door?
Door is locked when starting or using the oven
Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
How do I reset my Whirlpool oven after a power outage?
Look for “Control Lock” on the oven control console and then reset by typically holding the button(s) for 3 seconds.
How do I clear the error code on my Whirlpool dishwasher?
Press the “Heated Dry” button, followed by pressing the “Normal” button, and then press both buttons again in quick succession. Once you’ve pressed the two buttons twice, your dishwasher should go into a diagnostic mode, which will cause it to reset. If it doesn’t work, try doing it again with the door open.
How do I reset my F9 Whirlpool stove? Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
What does e09 mean on a Whirlpool washer? It means the overflow contacts on the water level pressure switch have been closed for more than 60 seconds. When this error occurs the central control unit will turn the drain pump on indefinitely as a safety precaution to keep the washer from flooding your home.
What is F9 on Whirlpool dishwasher? F9 (or 9 flashes) – Continuous water inlet. A dishwasher continuously fills with water for one of two most likely reasons. Either the inlet valve is faulty and is not closing or there is a short circuit on the main control board. The valve or control board may need to be replaced.
How do I clean my Whirlpool drain pump?
How do I put my Whirlpool oven in diagnostic mode?
Where is the drain pump on a whirlpool?
The drain pump assembly is directly in front of you, in the middle of the machine.
How do you clean a drain pump?
Where is drain pump filter on Whirlpool washer?
How do you clean a drain pump filter?
How do I manually drain my Whirlpool washer?
If not, follow these steps:
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose at the back of the washing machine.
- Step 3: Drain the water.
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose.
- Step 3: Drain the water.
- Step 4: Scrub the filter.
How do you clean a smelly washing machine drain?
